Hydraulic Shop Press Machines - H frame & C frame

DAKE H-FRAME HYDRAULIC PRESS

Made in USA

Standard Features:

• Hand Pump or Air or Electric
• Rapid Ram Return
• By-pass Hole
• Adjustable Table with self locking hoist
• Rapid Screw Traverse of Ram
• Movable Workload (except 25 ton)
• 2 Forged Steel V-Blocks & Table Plates
• Flat Ram Nose (except 25 ton)
• Pressure Gauge

Options Available:

• Air driven pump instead of hand pump
• Electric pump instead of hand pump
• Super-sensitive double-acting Ram Control
• Slide-out Table for overhead loading
• Stroke Indicator

DAKE HYDRAULIC DURA-PRESS

• Simple single acting cylinder design with 5 part oil seals for smooth operation and a tight seal.
• Welded heavy steel plate frame for greater rigidity.
• Efficient hand pump, conveniently located reduces operator fatigue.
• Each full stroke of the pump advances the ram 1/2".
• Preset factory sealed relief valve to prevent excessive pressure.
• Machine includes two forged steel table plates..
• Pressure gauge included.

DAKE ELECTRIC POWERED HYD. DURAPRESS

Same as above plus also includes:

• 1 Hp, 110 volt, single phase to plug in anywhere.
• Lever control arm advance.
• Double acting cylinder allows easy ram positioning.
• One hand ram positioning with 4-way hydraulic control.

DAKE 50 Ton HYDRAULIC DURA-PRESS

Made in USA

Click to Request a formal Quote for this machine

• Motor is 2 hp, 110 volts to plug in anywhere
• Lever control ram advance for easy use.
• Double acting cylinder for easy positioning of the ram.
• Sturdy, welded channel iron frame weighes over 1000 Lbs.
• Quiet, low pressure hydraulic systems for smooth pressing.
• One hand ram positioning with 4-way valve hydraulic control.
• Safety relief valve
• Joystick operation
• Two combination table plate/V-blocks
• Pressure gauge.
• Width between uprights: 44 inches [112cm]
• Width between table channels: 8.25 [21cm]
• Minimum ram to table: 0
• Maximum ram to table: 41 3/4 [106cm]
• Ram speed: 11 inches per minute
• Ram travel: 16 inches [40cm] C
• Machine weight: 1550 Lbs./ Size: 55 wide x 36 deep x 88" high

DAKE HYDRAULIC DURA-PRESS

• Double acting cylinder design with 5 part oil seals for smooth operation and a tight seal.
• Ram has lifting eyes to move table with chains.
• 2 Hp submerged motor drives 2 centrifugal pumps on 40 & 70 Ton
• 3 Hp submerged motor drives 3 centrifugal pumps on 100 Ton
• 220 or 440 Volts, 3 phase but electrical controls are low voltage.
• Ram rapid advance automatically shifts to slow after touching work.
• Machine has a pressure gauge and 2 forged steel plates.

HYDRAULIC MOVABLE TABLE PRESS

Made in USA

• Moveable Table allows overhead loading of heavy workpieces.
• Adjustable Workhead Height provides maximum daylight space for oversized work.
• Heavy-Duty Hoist easily raises and lowers workhead.
• Toggle Clamps lock table securely in place.
• Options available: Air driven hydraulics, electrically driven hydraulics, Table Plates, V-Blocks

EDWARDS HYDRAULIC SHOP PRESSES

20 ton tabletop model: $1999. // 40 ton:

$4299

60 ton $7499 // 110 ton

$10,999.

Click to Request our 40 Ton Press discounted Price with specifications

Click to Request our 60 Ton Press discounted Price with specifications

Click to Request our 110 Ton Press discounted Price with specifications

• Made in USA
• Heavy duty all steel construction
• Easy to use hand controls
• Quick disconnect hoses
• Stroke: 12 1/4" [20 ton: 6-1/4"]
• Width inside frame: ton: 20" // 40 ton: 38" // 60 ton: 42" // 110 ton: 48"
• Height inside frame: 20 ton: 10" // 40 ton 38" // 60 ton: 39" // 110 ton: 37"
• Optional 6 piece Tool Set for pushing
• Optional Programmable Logic Control for repeat work
• Optional Press Brake Tooling up to 32 inch long, can bend 3/16 x 32", 1/4 x 24", 3/8 x 6" wide.

These three Shop Presses are available as a plug in accessory to a new Edwards Ironworker machine that has the hydraulic accessory connector. If you do not have one you can buy the Hydraulic Power Unit for $3210. extra and is available in 230 volts 3 phase, 230 Volts 1 phase or 460 Volts 3 phase.

Optional Brake Press Tooling:

• 12 inches long $1530. extra
• 18 inches long $1760. extra
• 24 inches long $2230. extra
• 32 inches long $3060. extra

JET HYDRAULIC SHOP PRESS HP-15A

• Capacity: 15 Tons
• Easy-to-use, hand-operated hydraulic pump
• Pressure gauge for direct pressure readings
• Tables raise and lower easily with use of hand crank
• Side frames are open for inserting long material
• Fast setup ram extension screw
• Ram moves laterally for added versatility
• Two bed plates and pump handles
• Straightness testing support uses centers or v-blocks
• 2 year warranty

Click to Request a Quote for the Jet HP-15A

• Open Height: 17.5 inches
• Lateral Movement: 10-3/16"
• Net Weight: 435 Lbs
• Overall Dimensions: 33-7/8 x 29-1/2 x 65-1/2 inches
• Piston Stroke: 4-1/2"
• Ram Diameter: 2-1/2"
• Screw Stroke: 3-1/8"
• Vertical Table Travel: 22-3/16"
• Width: 35.5"
• Work Table Size (in.) 24-3/4 x 7-1/2 inches

JET HYDRAULIC SHOP PRESS HP-35A

• Capacity: 35 Tons
• Easy-to-use, hand-operated hydraulic pump
• Pressure gauge for direct pressure readings
• Tables raise and lower easily with use of hand crank
• Side frames are open for inserting long material
• Fast setup ram extension screw
• Ram moves laterally for added versatility
• Two bed plates and pump handles
• Straightness testing support uses centers or v-blocks
• 2 year warranty

Click to Request a Quote for the Jet HP-35A

• Open Height: 19.5 inches
• Lateral Movement: 15"
• Net Weight: 783 Lbs
• Overall Dimensions: 42-1/2 x 33-1/2 x 68 inches
• Piston Stroke: 4-3/4"
• Ram Diameter: 3"
• Screw Stroke: 4"
• Vertical Table Travel: 23-5/8"
• Width: 71"
• Work Table Size: 31 x 10-3/8 inches

H.M.I. PJP C-Frame Hydraulic Press

Made in USA

Choose from 42 Ton and 58 Ton Sizes

• 11" stroke
• 14" throat
• 18" throat height
• 38" x 16" press platen
• Motor: 10 HP

Click to Request a Quote for the PJP 42 Ton
Click to Request a Quote for the PJP 58 Ton

Features:

• Large open throat area
• Extra large press bed to accommodate a wide variety of tooling
• Easily switched over from die sets to single end punching
• Stroke can be stopped and reversed at any point in its cycle
• Full tonnage throughout stroke
• Reservoir mounted between housings for space savings
• Reservoir equipped with sight gauge and clean out ports
• Hydraulics have a return intank filter
• 12 month warranty.

Options:

• Ram diameter up to 8"
• Dual palm buttons
• Jog buttons for UP & DOWN
• Pressure reversal
• Tonnage control
• Punch package
• Safety Light Curtains
• Keyed Switches

HMI HYDRAULIC SEP C-FRAME PRESS

Made in USA!

Motor available in 208 volts, 230 volts or 460 volts.

Features:

Simple rugged design. Large open throat area. Extra large press bed to accommodate a wide variety of tooling. Easily switched over from die sets to single end punching. Long infinitely adjustable stroke 6" or 11" depending upon model. Stroke can be stopped and reversed at any point in its cycle. Full tonnage throughout stroke. Reservoir mounted between housings for space savings. Reservoir equipped with sight gauge and clean out ports. Hydraulics have a return intank filter. Tank prefilled by HMI, remote foot control.

Options:

• Ram diameter up to 8" available.
• Dual palm buttons.
• Jog buttons for UP & DOWN.
• Pressure reversal.
• Tonnage control.
• Punch package.
• Light Curtains.
• Keyed Switches.

DAKE C-FRAME HYDRAULIC PRESS

Standard Equippment:

• Adjustable Return Stroke
• Remote Pressure Adjustment
• Light Sensitive Thumb Pads
• Run-Jog Selector
• Oversized Heavy duty Hydraulic Cylinders
• Bolster Plate included
• Choose 208, 230, 460 or 575 volts, 3 phase.

Optional Equipment:

• Custom Bolster Plates
• Threaded or flanged Nose Piece
• Pedestals
• Air/oil Heat Exchanger
• Pressure and Distance Reversal Controls
• Variable Speed Control
• External Dwell timer
• Piece/Cycle Counter

Laboratory Compression Heat Press

With independently heated electric platens, precise temperature control, rapid advance hydraulics and accurate pressure adjustment. Designed to hold pressure for long periods. Use this machine for compression molding, laminating, testing, etc.

Click to Request a Quote on a 25 ton
Click to Request a Quote on a 50 ton
Click to Request a Quote on a 75 ton

Spring loaded Press Brake Die Set Assembly converts your hydraulic press into a Press Brake

Include: Upper die (punch) and 4 way bottom die.

V widths: 1/2 inch, 1 inch, 1.50 inch, & 2 inch wide.

Capacity:

• Frequent use: 1/4 inch mild steel, 10 gauge stainless
• Occasional use: 3/8 thick mild steel, 1/4 inch stainless
• Excessive loading of a 4 way die will crack it down the middle

Prices:

• 12 inches long: $1530
• 18 inches long: $1760
• 24 inches long: $2230
• 32 inches long: $3060

Turn your hydraulic shop press into an iron working machine with optional tooling:

Pipe Notcher

Notches pipe with a semi-circular cut to allow one pipe to fit 90° against another for railings. Then just a small amount of welding makes for a beautiful connection. Sizes from 1/2 to 2" schedule 40 pipe.

Rod Shear

Shears 1/4, 3/8, 1/2, 5/8, 3/4, and 1" diameter round rod cleanly and quickly.

Vee-Notcher

Cuts a 3 x 3 inch V-shaped notch in steel that is up to 1/4 thick. Very useful for notching angle iron.